EA 2010 Epoxy Activator
✆ How To Contact Us
The Mailing and Shipping Address for our physical location in Arkansas is:
Mailing & Shipping Address
R & E Paint Supply
57 Avalon Lane
Mountain Home, AR. 72653
Phone
Main Number: 1 (870) 425-8131
Toll Free: 1 (888) 709-8131
If you have any questions about products, how to purchase with us, or if you are unsure about anything, please contact us. You can contact us using the e-mail form below or you can contact us at the phone numbers listed above.
I Manufacturer Information
- Manufacturer
- CPS Coatings, Inc. / Autobahn Automotive Finishes
- Address
- 624 Airport Dr., Shreveport, LA 71107
- Product Information
- (318) 222-6100
- Emergency Telephone (CHEMTREC)
- 800-424-9300 (CCN 16851)
While we believe that the data herein is accurate and derived from quality sources, this data is not to be taken as a warranty or product liability. It is offered solely for your consideration and personal protection.
II Hazardous Ingredients
| Ingredients | CAS Number | Vapor Pressure (mm HG @ TEMP) | Weight Percent |
|---|---|---|---|
| *Xylene | 1330-20-7 | 9.5 mm Hg @ 68°F | 55–60% |
| *N Butyl Acetate | 123-86-4 | 7.8 mm Hg @ 68°F | 0–5% |
| Isopropyl Alcohol 99% | 67-63-0 | 31.2 mm Hg @ 68°F | 0–5% |
| *Glycol Ether EB | 111-76-2 | .88 mm Hg @ 68°F | <1% |
* Indicates toxic chemicals subject to the reporting requirements of section 313 of Title III and of 40 CFR 372.
III Physical Data
- Boiling Point
- 241° F
- Vapor Pressure (mmHg)
- @ 77°F = 23.0
- Vapor Density (Air = 1)
- Heavier than air
- Melting Point (°C)
- N/A
- Specific Gravity
- 0.9
- Solubility in Water
- None
- Evaporation Rate
- Slower than Ether
- Appearance and Odor
- Amber colored – solvent odor
- V.O.C.
- 4.8 lbs/gal
- Weight Solids
- 20–25%
IV Fire and Explosion Data
- Flash Point (Method Used)
- T.C.C., 60°F — Flammable
- Flammable Explosion Limits
- LEL = 1.0% · UEL = 12.3%
- Extinguishing Media
- (1) Dry Chemical, (2) CO2, (3) Foam
Special Fire Fighting Procedures
Dry Chemical, Carbon Dioxide, Water Spray or Regular Foam. Full protective equipment including self-contained breathing apparatus should be used. If water is used, fog nozzles are preferable. Water may be used to cool closed containers to prevent pressure buildup due to extreme heat. CAUTION: A straight stream of water will spread fire.
Unusual Fire and Explosion Hazards
Vapor accumulation will flash and/or explode if ignited. Containers may burst explosively if overheated in fire. Cool with water spray or fog. Empty containers also present fire explosion hazard due to residual vapors. Keep containers tightly closed. During emergency situations, over-exposure to decomposition products may cause a health hazard with no symptoms immediately apparent. Obtain medical attention.
V Health Hazard Data
Primary Routes of Entry
Inhalation, Ingestion, Skin Contact, Eye Contact
Acute Effects of Overexposure
Inhalation — Anesthetic. Irritation of respiratory tract or acute nervous system depression. Overexposure may result in headaches and nausea possibly followed by loss of consciousness.
Ingestion — Gastrointestinal irritation including vomiting can occur. Aspiration of material into lungs may result in chemical pneumonitis, which can be fatal.
Skin Contact — Liquids can be absorbed through the skin resulting in symptoms similar to the inhalation effects above.
Eye Contact — Will irritate.
Chronic Effects
Some reports have associated repeated, prolonged overexposure to solvents with permanent central nervous system changes. Misuse by concentrating and inhaling the contents may be harmful or fatal.
California Proposition 65 requires that warnings be given regarding exposures to chemicals listed by the State as being known to cause cancer, birth defects or other reproductive harm. This product is not intentionally formulated with chemicals that are listed by California as causing the above effects. However, the suppliers of some chemical ingredients used in this product inform us that they may contain trace, but detectable, levels of some listed chemicals as impurities. Therefore, trace, but detectable, levels of listed chemicals may be present in this product.
Emergency & First Aid Procedures
Vapor Inhalation
Restore breathing. Remove to fresh air. Keep warm and quiet. Notify a physician.
Eye Contact
Flush IMMEDIATELY with copious amounts of running water for at least 15 minutes. Take to physician for definitive medical treatment.
Skin Contact
Clean and wash affected area with water. Consult a physician if needed.
Ingestion
Drink 1 or 2 glasses of water to dilute. DO NOT INDUCE VOMITING! Call physician immediately.
VI Reactivity Data
- Stability
- Stable
- Conditions to Avoid
- Heat, open flames, electrical and static discharge.
- Incompatibility (Materials to Avoid)
- Strong oxidizers.
- Hazardous Polymerization
- Will not occur.
Hazardous Decomposition Products
May produce hazardous fumes when heated to decomposition as in welding.
VII Spill or Leak Procedures
Steps If Spilled
Ventilate area. Remove all possible sources of ignition. Avoid prolonged breathing of vapors. Confine spill with inert absorbent and clean up with spark-proof tools.
Waste Disposal
Dispose of in accordance with local, state, and federal regulations. Landfill or incinerate only in approved facility by licensed contractor. Do not incinerate in closed container.
VIII Special Protection Information
Respiratory Protection
Use NIOSH/MSHA TC23C Chemical / Mechanical type filter system to remove a combination of particles, gas & vapors. Use an air supplied respirator if necessary.
Ventilation
Use adequate ventilation in volume and pattern to keep TLV’s and PEL’s below recommended limits. General mechanical ventilation should comply with OSHA 1910.94.
Protective Gloves
To prevent prolonged exposure, use rubber gloves. Solvents may be absorbed through the skin.
Eye Protection
Safety glasses or goggles with splashguards or side shields.
Other Protective Equipment
Prevent prolonged skin contact to contaminated clothing.
IX Special Precautions
Handling and Storing
Observe label precautions. Keep away from heat, sparks and flame. Close container after each use. Ground containers when pouring. Wash all exposed areas thoroughly after handling and before eating or smoking. Do not store above 120°F.
Other Precautions
Do not sand, flame cut, braze or weld dry coating without a NIOSH/MSHA approved respirator or appropriate ventilation.
DO NOT TAKE INTERNALLY. IF INGESTED, DO NOT INDUCE VOMITING. CONSULT A PHYSICIAN. DO NOT FLAME CUT, WELD, OR BRAZE ON COATED MATERIAL WITHOUT NIOSH/MSHA TC23C RESPIRATOR.
WARNING: KEEP THIS AND ALL PAINT RELATED PRODUCTS OUT OF THE REACH OF CHILDREN!
Disclaimer
The information contained in this MSDS is based on data from sources considered to be reliable but we do not guarantee the accuracy or completeness thereof. We urge each customer or recipient of this MSDS to study it carefully to become aware of and understand the hazards associated with this product. The reader should consider consulting reference works or individuals who are experts in ventilation, toxicology or fire prevention as necessary or appropriate to use and understand the data in this MSDS.
Note: The data on this MSDS relates only to individual components and does not represent the end mixed product.
⚑ Hazard Identification (NFPA 704)
- Health — 2
- Flammability — 3
- Reactivity — 0
X Transportation Information
- DOT Shipping Name
- PAINT
- Hazard Class
- 3
- UN Number
- UN1263
- Packing Group
- II (2)
- Emergency Response Guide #
- 128